CHECK METER FUSE
Check the 10A fuse [No. 29, located in the fuse block (J/B)].
Is the fuse blown?
YES>>GO TO 2.
NO>>GO TO 3.
REPLACE METER FUSE AND CHECK AGAIN
Replace 10A fuse [No. 29, located in the fuse block (J/B)] and place ignition switch ON.
Does the fuse blow again?
YES>>Replace fuse and harness.
NO>>Inspection End.
CHECK HARNESS CONNECTIONS BETWEEN AIR BAG DIAGNOSIS SENSOR UNIT AND COMBINATION METER
Inspect the harness and connectors between the air bag diagnosis sensor unit and the combination meter.
Do the harness or connectors have any visible damage?
YES>>Replace harness.
NO>>GO TO 4.
CHECK COMBINATION METER
Disconnect the air bag diagnosis sensor unit harness connectors and place ignition switch ON.
Does AIR BAG warning lamp turn on?
YES>>Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.
NO>>Replace the combination meter. Refer to Removal and Installation.
CHECK CONDITION OF AIR BAG MODULE
Inspect for any deployed air bag modules or seat belt pre-tensioners.
Are any air bag modules or seat belt pre-tensioners deployed?
YES>>Refer to For Frontal Collision or For Side and Rollover Collision.
NO>>GO TO 2.
CHECK THE AIR BAG FUSE
Check 10A fuse [No. 29, located in the fuse block (J/B)].
Is the fuse blown?
YES>>GO TO 3.
NO>>GO TO 4.
CHECK AIR BAG FUSE AGAIN
Replace 10A fuse [No. 29, located in the fuse block (J/B)] and place ignition switch ON.
Does the fuse blow again?
YES>>Replace fuse and harness.
NO>>Inspection End.
CHECK AIR BAG DIAGNOSIS SENSOR UNIT
CONSULT
Is “AIR BAG” displayed on CONSULT?
YES>>GO TO 5.
NO>>Visually inspect the air bag diagnosis sensor unit harness connections. If the connections are OK, replace the air bag diagnosis sensor unit. Refer to Removal and Installation.
CHECK HARNESS CONNECTION
Check for loose connections between the combination meter and the air bag diagnosis sensor unit.
Are there any loose connections?
YES>>Properly connect the combination meter and air bag diagnosis sensor unit harness connectors. If AIR BAG warning lamp still does not turn off, replace the wiring harness.
NO>>Replace air bag diagnosis sensor unit. Refer to Removal and Installation.
SEAT BELT WARNING LIGHT
Place ignition switch to ON.
Does the seat belt warning lamp come ON?
YES>>GO TO 2.
NO>>Check 10A fuse [No. 15, located in the fuse block (J/B)].
Check seat belt buckle switch LH.
Check harness between combination meter and seat belt buckle switch LH.
Check combination meter. Refer to Fail-Safe.
SEAT BELT BUCKLE LH
Fasten the seat belt buckle LH.
Does the seat belt warning lamp go OFF?
YES>>GO TO 3.
NO>>Check seat belt buckle switch LH.
Check harness between combination meter and seat belt buckle switch LH.
OCCUPANT CLASSIFICATION SYSTEM
Have a helper sit in the passenger seat.
Does the seat belt warning lamp go ON?
YES>>GO TO 4.
NO>>Check occupant classification system. Refer to System Description.
Check harness between occupant classification system control unit and air bag diagnosis sensor unit.
SEAT BELT BUCKLE RH
Fasten the seat belt buckle RH.
Does the seat belt warning lamp go OFF?
YES>>System OK.
NO>>Check seat belt buckle switch RH.
Check harness between seat belt buckle switch RH and air bag diagnosis sensor unit.
Check harness between seat belt buckle switch RH and occupant classification system control unit.
Replace air bag diagnosis sensor unit. Refer to Removal and Installation.
SRS air bag warning lamp is OFF, passenger air bag indicator lamp turns ON intermittently with a person of adult stature seated normally in the passenger seat.
REPLACE OCS SENSORS
Replace the OCS sensors. Refer to Removal and Installation.
Perform zero point reset. Refer to Description.
Is symptom still present?
YES>>GO TO 2.
NO>>Inspection End.
REPLACE PASSENGER SEAT CUSHION FRAME
Replace the passenger seat cushion frame. Refer to Seat Cushion.
Perform zero point reset. Refer to Description.
>>
Inspection End.
Vehicle conditions:
Seat belt indicator lamp is ON, passenger air bag indicator lamp is ON or OFF
Passenger seat is unoccupied
Driver seat belt is buckled
Passenger seat belt buckle harness and seat belt buckle switch are OK (buckle passenger seat belt to check if seat belt indicator lamp turns OFF, driver seat belt needs to be buckled)
REPLACE OCS SENSORS
Replace the OCS sensors. Refer to Removal and Installation.
Perform zero point reset. Refer to Description.
Is symptom still present?
YES>>GO TO 2.
NO>>Inspection End.
REPLACE PASSENGER SEAT CUSHION FRAME
Replace the passenger seat cushion frame. Refer to Seat Cushion.
Perform zero point reset. Refer to Description.
>>
Inspection End.
Nissan Pathfinder Info Center
Email: info@nipathfinder.com
Phone: +1 (800) 123-4567
Address: 123 Pathfinder Blvd, Nashville, TN 37214, USA
Working Hours: Mon–Fri, 9:00 AM – 5:00 PM (EST)