Nissan Pathfinder: Meter, Warning Lamp & Indicator - Symptom Diagnosis

• Meter System Symptoms
• Head up Display Symptoms
• Normal Operating Condition

Meter System Symptoms Nissan Pathfinder 5th Gen

The Low Washer Fluid Warning Continues Displaying, or Does Not Display

Diagnosis Procedure

• The warning is still displayed even after washer fluid is added.

• The warning is not displayed even though the washer tank is empty.

CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT

Check the washer fluid level switch signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness or connector.

CHECK WASHER FLUID LEVEL SWITCH

Check the washer fluid level switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace washer fluid level switch. Refer to Removal and Installation.

The Fuel Gauge Indicator Does Not Operate

Description

Fuel gauge will not indicate from a certain position.

Diagnosis Procedure

PERFORM COMBINATION METER SELF-DIAGNOSIS MODE

Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally. Refer to On Board Diagnosis Function.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the combination meter. Refer to Removal and Installation.

CHECK FUEL LEVEL SENSOR UNIT CIRCUITS

Check the fuel level sensor circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning part.

CHECK FUEL LEVEL SENSOR UNIT

Check the fuel level sensor unit. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace fuel level sensor unit. Refer to Removal and Installation.

CHECK FLOAT INTERFERENCE

Check that the float arm does not interfere with or bind to other components in the fuel tank.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace fuel level sensor unit. Refer to Removal and Installation.

The Steering Switches Are Inoperative

Description

If any of the following malfunctions is found for the steering switch operation.

• All switches are inoperative

• The specified switch cannot be operated

Diagnosis Procedure

CHECK STEERING SWITCH SIGNAL A CIRCUIT

Check the steering switch signal A circuit. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace malfunctioning parts.

CHECK STEERING SWITCH SIGNAL B CIRCUIT

Check the steering switch signal B circuit. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning parts.

CHECK STEERING SWITCH

Check steering switch resistance. Refer to Component Inspection (steering switch signal A) or Component Inspection (steering switch signal B).

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace steering switch. Refer to Removal and Installation.

The Illumination Control Switch Is Inoperative

Description

If any of the following malfunctions is found for the illumination control switch operation.

• All switches are inoperative

• The specified switch cannot be operated

Diagnosis Procedure

CHECK ILLUMINATION CONTROL SWITCH SIGNAL CIRCUIT

Check the illumination control switch signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK ILLUMINATION CONTROL SWITCH

Perform a unit check for the illumination control switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace illumination control switch. Refer to Removal and Installation.

The Master Speaker Does Not Sound

Description

The master speaker does not sound.

Diagnosis Procedure

CHECK COMBINATION METER INPUT SIGNAL

CONSULT

1. Select “BUZZER” in “Data Monitor” mode of “METER/M&A”.

2. Check that the function operates normally according to the following conditions:

   Monitor item	Condition	Status
   BUZZER	Under the condition of buzzer input	ON
   	Except above	OFF

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace BCM. Refer to Removal and Installation.

CHECK MASTER SPEAKER CIRCUIT

Check master speaker circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

The Ambient Temperature Display Is Incorrect

Description

• The displayed ambient air temperature is higher than the actual temperature.

• The displayed ambient air temperature is lower than the actual temperature.

Diagnosis Procedure

NOTE:

Check that the symptom is not applicable to the normal operating condition before starting diagnosis. Refer to Description.

CHECK AMBIENT SENSOR SIGNAL CIRCUIT

Check the ambient sensor signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace malfunctioning parts.

CHECK AMBIENT SENSOR

Check the ambient sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace ambient sensor. Refer to Removal and Installation.

Head up Display Symptoms Nissan Pathfinder 2025

Head up Display Screen Is Not Displayed

Diagnosis Procedure

CHECK HEAD UP DISPLAY SWITCH OPERATION

CONSULT

1. Ignition switch ON.

2. Select "Main switch" in "Data Monitor" mode of "E-HUD".

3. Check that the function operates normally according to the following conditions:

   Monitor item	Condition		Indication
   Main switch	Head Up Display switch	Press the switch	On
   		Except above	Off

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK HEAD UP DISPLAY UNIT POWER SUPPLY CIRCUIT

Check the head up display unit power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace head up display unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

CHECK HEAD UP DISPLAY SWITCH SIGNAL CIRCUIT

1. Ignition switch OFF.

2. Disconnect head up display unit harness connector and head up display switch harness connector.

3. Check the continuity between head up display unit harness connector and head up display switch harness connector

   Head up display unit		Head up display switch		Continuity
   Connector	Terminal	Connector	Terminal
   M107	13	M118	6	Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness or connector.

CHECK HEAD UP DISPLAY SWITCH

Check the head up display switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace head up display unit. Refer to Removal and Installation.

NO>>

Replace head up display switch. Refer to Removal and Installation.

Head up Display Brightness Is Not Changed

Diagnosis Procedure

CHECK HEAD UP DISPLAY BRIGHTNESS ADJUSTMENT SIGNAL

CONSULT

1. Select "Display brightness" in "Data Monitor" mode of "E-HUD".

2. Check that the function operates normally according to the following conditions:

   Monitor item	Condition	Indication
   Display brightness	Press brightness adjustment on the combination meter setting screen.	The display changes from (-10) to (10)

Is the inspection result normal?

YES>>

Replace head up display unit. Refer to Removal and Installation.

NO>>

Check combination meter self diagnosis result. Refer to DTC Index.

Head up Display Screen Is Not Displayed in the Correct Position

Diagnosis Procedure

CHECK HEAD UP DISPLAY POSITION ADJUSTMENT SIGNAL

CONSULT

1. Select "Data Monitor" mode of "E-HUD".

2. Check that the function operates normally according to the following conditions:

   Monitor item	Condition	Indication
   Display up and down status	Press each position adjustment on the combination meter setting screen.	The display changes to (-10) - (10)
   Display rotation status		The display changes to (-10) - (10)

Is the inspection result normal?

YES>>

Replace head up display unit. Refer to Removal and Installation.

NO>>

Check combination meter self diagnosis result. Refer to DTC Index.

Normal Operating Condition Nissan Pathfinder Fifth generation

Information Display

Description

DISTANCE TO EMPTY

The calculated distance to empty may differ from the actual distance to empty if the refueling amount is approximately 6 (1 1/2 US gal,1 1/2 Imp gal) or less. This is because the refuel control (moves the fuel gauge needle quicker than normal judging that the driver is refueling the Nissan Pathfinder vehicle) is not performing.

AMBIENT TEMPERATURE

The displayed ambient temperature on the information display may differ from the actual temperature because it is a corrected value calculated from the ambient sensor signal by the combination meter. Refer to System Description for details on the correction process.

Head up Display

Symptom Description

The head up display unit controls and protects the backlight and display when the LED temperature becomes high. Refer to Protection Function.